They don’t really work in wind, and they aren’t the quietest, but they are as stealthy as you can get, looking just like earbuds. A decade ago you still looked a little bit of a geek using them and monitoring on a recorder, but nowadays most people are looking at their smartphones, rather than the lamp-post/road they are about to encounter. On the off-chance that they do look up, they will assume you are just another human trying to escape the real world for the virtual one inside your phone, which happens to be a field recorder.
I was going for a general recce on the Somerset levels, looking for interesting sounds. I heard a lot of birds congregating in some trees, and started the OKMII. There was a lovely little flurry of about 100 starlings flying overhead at about 2 and 4 secs against a background of other starlings gathering in the trees
The OKMII isn’t really a birding mic, but it picked up some of the essence of these guys
and then I encountered this ghastly full-scale 0dBFS noise on the left
a bad contact on the left channel. After 10 years these mics don’t owe me anything, but I figured it’s worth a look if a fix is possible. Skinning the foam earpads shows this
It’s possible to separate these with a craft knife along the obvious seam, concentrating on the melted bits. The microphone is glued to the shell with a hole, try and keep this together to expose the contacts on the rear of the capsule. Continue reading “Soundman OKMII repair”
Like most field recordists I use the metering the manufacturers give me on field recorders, and that’s fine for most stereo and binaural applications. But it does have its limitations, particularly for mono compatibility. Unlike a studio situation in the field you are recording what is out there, the only thing you can change is your physical location and the direction you are facing. Des Coulam of soundlandscapes had the concept of the sound map and using that has helped me with with urban field recordings. With bird recording it’s simple – get as close as you can to the bird without disturbing it 😉 If using a directional microphone then you want to position the interference in the dead zone of the mic.
Most people on the Internet seems to listen in stereo, there aren’t going to be that many PC users hooking the output of their audio card into their 1950s valve gramophone. So binaural urban field recordings are going to be fine because if anyone listens they will be listening in stereo and most likely using headphones, which is a great mix. You get decent results even from highly reverberant recordings like the South Kensington Station pedestrian tunnel.
The trouble with binaural is you end up with a lot of out-of-phase signals, the classic ball of string on a goniometer studio display. With the pedestrian tunnel I tried to keep the busker central while recording, and this is serviceable in that recording. Nevertheless there are a few places where the ball of string stretches out horizontally, and mixing the signal to mono worsens the tone of the recording – the echo that was character now become colouration.
Birds are harder in binaural stereo
They are higher in pitch, and they also aren’t in a horizontal plane.
I tried hard to keep this Robin central
but I didn’t think about the vertical plane at all. You don’t, normally, because when you are recording people or anything else they are usually in front of you 🙂
it was about 5m away in a tree, the vertical angle was about 45 degrees.
There’s about 270 degrees phase shift, hence the round goniometer display. The dominant frequency is about 4kHz, working out the path length that corresponds to that, from
velocity=frequency x wavelength
so λ=v÷f , ie λ = 330/4000 = 0.08m or 8 cm. A 90 degree phase shift would be picked up from a 2cm path difference between my ears and the robin’s bill. To try and reduce this I need to be a lot more careful about orientating my head to the bird; I’m glad we don’t normally use binaural recording for birdsong from individuals[ref]as can be heard in this poor recording, it’s hard to get enough discrimination against background noise with binaural. That’s just not what binaural is about, but it excels at, say a rook roost or a starling roost[/ref]
Unfortunately the Telinga parabolic microphone system, in particular the DATmic also has this, because there is a baffle between the two stereo sides. One of the nice things about the Telinga is that you get the background in stereo and the wanted sound in mono.
With this swallow recording this seems to hold at the start, but drift off
It was recording using a Telinga dish and DATmic at the WSRS Ennerdale field recording meeting. The bird was sitting on a phone wire just outside the bunkhouse, I was on the first floor so roughly level with the bird about 2m away aiming out of a window. It was a handheld, snatched recording – you have to seize the moment sometimes. And I probably let the dish drift slightly.
We don’t use phase information, or interaural time differences above about 1.5kHz
Sitting at home I can hear the difference between the first part and the second part – the first part of this clip has better definition. But it isn’t easy to get this right in the field by ear alone. It appears that high-frequency stereo location above 1500 Hz is by intensity rather than phase – there seems to be some sort of phase-locking mechanism that improves low frequency discrimination by interaural phase. Which is just as well since low frequencies are masked less by the head.
Although I knew that we use both phase and intensity to derive the stereo image I didn’t appreciate the frequency dependence. This is also used in MP3 encoding, so I need to learn more about that to be able to MP3 encode field recordings better – they would lend themselves well to joint stereo modes.
This means I am sunk as far as getting the robin’s song in phase by ear. I’m just not going to hear it – I need some kind of gizmo to show me this visually.
As to whether this is practically useful in the field is another matter. Birds have a nasty habit of moving, I’m guessing a robin won’t move enough while singing to pick up an extra 2cm path length, but I don’t know.
A smartphone might be man enough in the processing FLOPS department to show the oscilloscope goniometer display directly, which is the non plus ultra of stereo display. But
I’d need to write the app
I only have an iPod touch and
the audio in is mono only
I’ll file that in the too hard department for now. There’s already more than enough to wrangle in the field and I only have two hands…
The scope display is too much to tote around, while I do have a DS0203 digital scope, the user interface of that is fiddly and terrible. It’s acceptable on the bench and there are times you just need an isolated scope, but it would be maddening in the field.
There are three other types of stereo phase display I know of.
One is the sort of thing described in Westhost’s Project 135 – Stereo Phase Correlation meter. I’ve never seen one of these.
At the BBC they tended to measure the sum and difference levels and display these. It’s possible to do that using a single LED display by running the L+R signal to one log display and the L-R signal to another, and using bicolour LEDs, green to the L+R and red to the L-R. If you see red then there’s too much out of phase data.
The last is the Frank Fox ‘The Box’ using a square of LEDs. Oy vey – £450, I don’t think so. To go that way I need to work out how they do it, and preferably make it smaller…